7A 160W Dual Motor Drive Module DC 12V/24V PWM H-bridge L298 Logic Control Board

Description

7A 160W Dual Motor Drive Module DC 12V/24V PWM H-bridge L298 Logic Control Board
Product Highlights:
1. Double H bridge, which can drive two DC motors with single 7A current, high power;
2. Wide voltage input 6.5V ~ 27V;
3. Signal optocoupler isolation input, IO port can be directly controlled, without interference;
4. Undervoltage protection, to prevent instantaneous high-current burned module;
5. High-power TVS and electrostatic discharge circuit, inhibit the transient interference pulse and static, enhanced EMC performance, stable and reliable product, industrial design.
Control signal logic
Note
: Where 0 is low, 1 is high level, × is any level, when floating high.
1. 1 # motor interface control signal logic
IN1
IN2
ENA1
OUT1
.
OUT2
0
0
×
brake
1
1
×
Floating
1
0
PWM
Forward to speed
0
1
PWM
Reverse speed
1
0
1
Full speed forward
0
1
1
Full speed reversal
2. 2 # motor interface control signal logic
IN3
IN4
ENA2
OUT3
.
OUT4
0
0
×
brake
1
1
×
Floating
1
0
PWM
Forward to speed
0
1
PWM
Reverse speed
1
0
1
Full speed forward
0
1
1
Full speed reversal
Product parameters:
1. Power supply voltage 6.5V-27V, power supply must not be connected to or over 27V, otherwise it may                burn out the module, it is recommended that the power input in series 15A fuse.
2. Dual motor interface, each rated output current 7A, peak current 50A, the motor interface must not                        short-circuit, the proposed series 10A fuse.
3. Control signal voltage 3-6.5V, respectively, is the enable signal and the positive inversion control signal.
4. Enable signal terminal (ENA) input PWM adjustable speed, PWM frequency range 0-10KHZ, PWM                     minimum pulse width 10us.
5. Working temperature -25 ℃ -80 ℃.
6. Product size: 55 x 55 x 16mm (length and width).
7. Installation hole diameter: 3mm, attention should be paid to prevent short circuit on the back of the                       circuit, you can add insulation pad or copper column to raise the circuit board.
Suitable for motor parameters:
Rated voltage 24V of the motor, the appropriate identification of rated power 115W and below or rated current of 7A or less the following long-term work of the motor.
Rated voltage 12V of the motor, the appropriate identification of rated power 40W and below or rated current 7A rated below the motor for a long time full of work.
Precautions
:
1. Drive power must not be reversed, the proposed power connector in series 15A fuse, the voltage should             be between 6.5 ~ 27V. If the voltage is over-voltage, power-on may burn the drive module.
2. It is recommended that the rated output current of the power supply should be at least 2 times of the rated           current of the motor so that the power supply can not supply the required voltage when the motor starts. Off         the output lead to the phenomenon of motor pause.
3. Do not short-circuit the motor interface, or may burn the driver module, the proposed electrical interface     in       series 10A fuse.
4. In the forward and reverse switch when the need to brake 0.1S above and then reverse, not in the                         motor has not stopped when the commutation, or it may damage the drive.
5. Drive module power-down, do not directly or indirectly, high-speed rotation of the motor, or motor                         generated electromotive force may burn the drive module.
If the application requires a high-speed rotation of the motor when the drive module is powered down, it is           recommended that the motor interface of the driver is connected in series with a relay (NO and COM                   terminals), and the relay coil and the driver are connected in common. In this way, when the power                         down, the relay will disconnect the drive and the motor connection.
6. CAUTION Do not expose the drive to moisture. Do not short-circuit the components on the drive board.     Do      not touch the pins and pads on the board.
7. Before you use the baby carefully read the description, as a result of damage caused by improper use of           the module, do not change.
Package Include:
1 x  7A 160W Dual DC Motor Drive Module Positive Negative PWM Speed L298 Logic XY160D
Shipping
Feedback
Contact us
Return Policy
Shipping
Domestic
We believe you need to get your purchases as quick as possible. As a general rule your item will be shipped within 24 hours of you purchasing it. We pack and post from Tuesday to Sunday (Mondays we are closed) but definitely get all our mail off to the post office first thing Monday morning for you. Mail gets picked up at 12pm so chances are if you buy before lunchtime your item will leave the same day.
International
Same as above but understand that depending on what part of the world you are from it does take a little longer to send, delivery can be from 7-15 working days. Also other factors to take into consideration are quarantine and customs regulations in your country. It is also a consideration that customs duties and GST/VAT may be payable at the buyers expense.
Combined Postage (for items with shipping charges):
We are more than happy to combine postage, just use the Buy it Now function in eBay (but DO NOT PAY after purchasing each item) to buy all the products you need, when you have finished request a combined invoice, we will base the shipping cost on the size, weight and your location.
Feedback
* When you satisfied with our product and services please leave us positive feedback.
* If you have got the package, please confirm "
Delivery on time
" For us.
* If a problem occurs, contact us immediately with any email request.
* Just contact us using the "
Ask the seller a question
" link on eBay.
Your Satisfaction is our Priority. Our goal is to make all our customers as happy as possible while shopping with us.
Contact us
For anything problem about product, price, shipping or order status, pleasecontact us via eBay message.Just contact us using the "
Ask the seller a question
" link on eBay.
We expect positive feedback and 5 scores DSR  from you.
Return Policy
We believe our items are so outstanding. We are convinced you will be happy with your Purchase.
If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund to you after the returned item arrived at our warehouse.
Please include your eBay ID and item number with any email requests.