USA Free! 3Axis Wantai Stepper Motor Driver DQ860MA 80V 7.8A 256Micro For Nema34

Description

Welcome to my Store!
Ship from
USA
warehouse ,
after payment, within 3 days for receiving products!
No taxes from customs, no damage, better service, please don't hesitate! Free Ship by
UPS
!
This item includes:
3PCS Stepper Motor Driver DQ860MA 7.8A 80V 256Microsteps
1PC Breakout Board&cable
Pls confirm the shipping method and shipping fees before pay!
Feel free to contact me for any question!
Stepper Motor Driver:DQ860MA
Introduction:
DQ860MA is a type of two-phase hybrid stepping motor driver, the drive voltage of it is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 110mm outside diameter and less than 7.8A phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Holding torque when DQ860MA run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on
.
Features:
l
High performance, low price
l
Average current control, 2-phase sinusoidal output current drive
l
Supply voltage from 24VDC to 80VDC
l
Opto-isolated signal I/O
l
Overvoltage, under voltage, overcurrent, phase short circuit protectio
l
14 channels subdivision and automatic idle-current reductio
n
l
8 channels output phase current setting
l
Offline command input termina
l
l
Motor torque is related to speed, but not related to step/revolution
l
High start speed
l
High hording torque under high spe
ed
Electrical specification:
Input voltage
24-80VDC
Input current
＜
6
A
Output current
2.8A
～
7.8A
Consumption
Consumption
：
80W
；
Internal Insurance
：
10
A
Temperature
Working Temperature
-10
～
45
℃
；
Stocking temperature
-40
℃
～
70
℃
Humidity
No condensation, no water droplets
gas
Prohibition of combustible gases and conductive dust
weight
500G
Pins assignments and description:
Connector Pins    Configurations
Pin Function
Details
PUL +,PUL-
Pulse signal, PUL+ is the positive end of pulses  input pin
PUL- is the negative end of pulse  input pin
DIR+,DIR-
DIR signal: DIR+ is the positive end of direction input pin
DIR- is the negative end of direction input pin
ENBL+
Enable signal:  ENBL+ is the positive end of direction input pin. This signal is used for enabling/disabling the driver. High level for enabling the driver and low level for disabling the driver.
ENBL-
ENBL- is the negative end of direction input pin. Usually left unconnected (enabled)
Function choice ( Using DIP pins to achieve this function)
1) Micro step resolution is set by SW 5,6,7,8 of the DIP switch as shown in the following table:
SW5
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
SW6
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
SW7
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
SW8
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
PULSE/REV
400
800
1600
3200
6400
12800
25600
51200
1000
2000
5000
10000
25000
50000
2) Standstill current setting
SW4 is used for this purpose. OFF meaning that the standstill current is set to be half of the selected dynamic current and ON meaning that standstill is set to be the same as the selected dynamic current.
3) Output current setting:
The first three bits (SW 1, 2, 3)of the DIP switch are used to set the dynamic current. Select a setting
Closest to your motor’s required current
Output current (A)
SW1
SW2
SW3
PEAK
RMS
ON
ON
ON
2.80
2.00
OFF
ON
ON
3.50
2.50
ON
OFF
ON
4.20
3.00
OFF
OFF
ON
4.90
3.50
ON
ON
OFF
5.70
4.00
OFF
ON
OFF
6.40
4.60
ON
OFF
OFF
7.00
5.00
OFF
OFF
OFF
7.80
5.60
4) Semi-flow  function:
Semi-flow function is that there is not step pulse after200 ms, the driver output current automatically reduced to 40% of rated output current, which is used to prevent motor heat.
Pins of motor & power:
Motor and power pins
1
A+
Motors wiring
2
A-
3
B+
4
B-
5,6
DC+
DC-
Power supply
Power supply
：
DC24-80VDC
The peak input current can not up to 6A
Breakout Board:DB25
Set pins according to software as follows:
Output pin: P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17
.
l
P2
–
X axis Pulse, P3 – X axis Direction
l
P4
–
Y axis Pulse, P5 - Y axis Direction
l
P6
–
Z axis Pulse, P7 – Z axis Direction
l
P8
-
A axis Pulse, P9 - A axis Direction
l
P14
-
B axis Pulse, P1- B axis Direction
l
P16
-
C axis Pulse, P17- C axis Direction
Input pin
:
P10 ,P11, P12, P13
,
P1
5
l
Set
them for Emergency Stop and X Y
Z Limit switch
Problem and feedback:
Please give us the opportunity to resolve any problem when you have, we will try our best to help you.
Your satisfaction is is of the utmost importance for us, so please contact us before you want to leave a negative feedback.
Refund:
If you are not satisfied with the package, please tell us the reason.
Delivery cost must be paid by the buyer.
Honor:
Changzhou Wantai Electrical Appliance Co.,Ltd has powerful technology, mature technics and complete testing equipment. And we have obtained ISO9001:2000 certification, CE certification and all of our products conform to RoHS requirements.
Note:
we can manufacture products according to our customer's requirements.
Appliaction:
Our product are mainly used in Aerospace & Defense, Automation Applications, Commercial Equipment, Industrial Tool, Medical Device & Equipment, Medical Mobility, Printing & Imaging, Pump, Semiconductor Equipment, Vehicle, , Milling Machine, Engraver Machine, CNC Routers Applications,etc.
Contact US:
Changzhou
Wantai Electrical Appliance Co.Ltd
Tel:0086-519-85138377
Fax:0086-519-85139178
Contact: Ada