Wantai CNC 4Axis Nema34 Stepper Motor 1090oz-in 5.6A+Driver 80V 7.8A

Description

This Item includes:
4PCS Nema 34 Stepper Motor with 1090oz-in (7.7N.m) holding torque,5.6A current,99mm motor body length,
4PCS Driver DQ860MA with 7.8A peak current ,24-80VDC ,256 Microstep
4PCS Power Supply:350W  60V
1 PC Breakout board&cable is
free offered
1, Stepper Motor
Technical Specifications
Part No.:                      85BYGH450D-008
single shaft
Frame Size:                NEMA34
Step Angle:                 1.8 degree
Voltage:                       2.13V
Current:                       5.6
A
/phase
Resistance:                 0.38 Ohm/phase
Inductance:                 4.1 mH/phase
Holding torque:           7.7
N.m
1090
oz
-in
Rotor inertia:               1700
g
-cm2
Number of wire leads: 4
Weight:                          3
kg
Length:                         99
mm
RED           A+
GREEN      A-
YELLOW    B+
BLUE         B-
Please tell us if you need Double shaft or single shaft, we can manufacture both for you. If you need Double shaft, please tell us your requirements for length of front and rear shaft, as well as the diameter. So that we can offer you the quite good products, thanks!
If you need customer designed size, please tell us your requirements for length of front and rear shaft, as well as the diameter. So that we can offer you the quite good products, thanks!
2, Stepper Motor Driver DQ860MA
DQ860MA
Introduction,Features and Applications
Introduction
DQ860MA is a type  of two-phase hybrid stepping motor driver, The drive voltage of which is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with
57mm
to
110mm
outside diameter and less than
8.0A
phase current. This circuit that it adopts is similar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DQ860MA run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on.
Features:
l
High performance, low price
l
Average current control, 2-phase sinusoidal output current drive
l
Supply voltage from 24VDC to 80VDC
l
Opto-isolated signal I/O
l
Overvoltage, under voltage, overcorrect, phase short circuit protection
l
14 channels subdivision and automatic idle-current reduction
l
8 channels output phase current setting
l
Offline command input terminal
l
Motor torque is related with speed, but not related with step/revolution
l
High start speed
l
High hording torque under high speed
Electrical specification:
Input voltage
24-80VDC
Input current
＜
6A
Output current
2.8A
～
7.8A
Consumption
Consumption
：
80W
；
Internal Insurance
：
10A
Temperature
Working Temperature -10
～
45
℃
；
Stocking temperature
-40
℃
～
70
℃
Humidity
Not condensation, no water droplets
gas
Prohibition of combustible gases and conductive dust
weight
500G
3, Power Supply 350W,60VDC
4, Breakout Board DB25
Description:
Built in DB25 male connector.
DB25 Output Pin:P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17.
DB25 Input Pin: P10,P11,P12,P13,P15.
DB25 GND Pin: P18-P25.
Power supply: +5V DC.
Built in C-class Optical-coupler.
High quality with Surface-mount Tech.
We ship worldwide!